| Items 1 to 14 of 14 |
| Items 1 to 14 of 14 |
Poly Pipe Punch - Tubing Cutter - Emitter Inserter
This drip tube irrigation tool will help get you through any irrigation project with ease. Use for easy cutting of poly irrigation line or soaker hose, up to .940". A great tool for home gardeners and professional landscapers.
Features:
For Poly Punch:
Place tubing crescent against tubing. Apply downward pressure until punch pin pierces tubing. Release. Periodically wipe punch pin with fingers to remove resin build up.
For Emitter/Barb insert:
Insert emitter or barb into upper barb holder. Place emitter or barb against punch hole in tubing. Apply pressure until emitter barb pierces tubing. Remove tool.
For Emitter/Barb Insert with 1/4'" Tubing:
Install emitter with ¼" tubing attached into small crescent slots on bottom of tool. Place shoulder of emitter on outside edge tool with ¼" tubing pressed into smaller crescents. While holding emitter assembly in crescents, place emitter barb against punch hoe in tubing. Apply pressure until emitter barb pierces tubing. Remove tool.
For emitter removal:
Place eased edge on bottom of punch handle against emitter at 45 degree angle. Apply pressure until emitter edge is lifted and seated into crescents. While holding emitter assembly in crescents rotate tool backwards until emitter is removed.
Tubing Cutter:
Lightly squeeze handles together while rotating them up and down. As tubing is cut release pressure at the end of cut.
When laying out your drip irrigation systems mainline, it is important to secure the tubing. The Galvanized Tubing Holder is an ideal accessory for holding poly tubing in its place on the ground. Galvanized to provide a sturdy, rust-proof tubing stake.
1/4" barb coupling is used to joint two ends of 1/4" micro tube together.
Also, attach the 1/4 "pipe by inserting the other end into a 1/2" or 3/4 "pipe.
1/4" Barbed Drip Fittings are used in the installation of all brands of 1/4" micro tubing, 1/4" drip line, and 1/4" soaker hose. The barbed fittings are pushed into the inside diameter of the 1/4" micro tubing, 1/4" drip line and 1/4" soaker hose for a very tight-fitting connection. The barbed fittings can be used for a two-way layout or for three-way layout of micro tubing, drip line, or soaker hose. The 1/4" barbed fittings are used to connect the end of all brands of 1/4" micro tubing with .140 ID to .170 ID. The barbed fittings can also be used to attach the micro tubing to the 1/2" or 3/4" drip tubing.
1/4" barbed fittings are made of high impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss and a range of drip emitter, bubbler, and micro sprayer flow rates leading to greater installation flexibility.
Features
Ways to use 1/4" micro irrigation fittings.
Typical installation.
1/4" barb coupling is used to joint two ends of 1/4" micro tube together.
Also, attach the 1/4 "pipe by inserting the other end into a 1/2" or 3/4 "pipe.
1/4" Barbed Drip Fittings are used in the installation of all brands of 1/4" micro tubing, 1/4" drip line, and 1/4" soaker hose. The barbed fittings are pushed into the inside diameter of the 1/4" micro tubing, 1/4" drip line and 1/4" soaker hose for a very tight-fitting connection. The barbed fittings can be used for a two-way layout or for three-way layout of micro tubing, drip line, or soaker hose. The 1/4" barbed fittings are used to connect the end of all brands of 1/4" micro tubing with .140 ID to .170 ID. The barbed fittings can also be used to attach the micro tubing to the 1/2" or 3/4" drip tubing.
1/4" barbed fittings are made of high impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss and a range of drip emitter, bubbler, and micro sprayer flow rates leading to greater installation flexibility.
Features
Ways to use 1/4" micro irrigation fittings.
Typical installation.
1/4" barb coupling is used to joint two ends of 1/4" micro tube together.
Also, attach the 1/4 "pipe by inserting the other end into a 1/2" or 3/4 "pipe.
1/4" Barbed Drip Fittings are used in the installation of all brands of 1/4" micro tubing, 1/4" drip line, and 1/4" soaker hose. The barbed fittings are pushed into the inside diameter of the 1/4" micro tubing, 1/4" drip line and 1/4" soaker hose for a very tight-fitting connection. The barbed fittings can be used for a two-way layout or for three-way layout of micro tubing, drip line, or soaker hose. The 1/4" barbed fittings are used to connect the end of all brands of 1/4" micro tubing with .140 ID to .170 ID. The barbed fittings can also be used to attach the micro tubing to the 1/2" or 3/4" drip tubing.
1/4" barbed fittings are made of high impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss and a range of drip emitter, bubbler, and micro sprayer flow rates leading to greater installation flexibility.
Features
Ways to use 1/4" micro irrigation fittings.
Typical installation.
1/4" barb coupling is used to joint two ends of 1/4" micro tube together.
1/4" Barbed Drip Fittings are used in the installation of all brands of 1/4" micro tubing, 1/4" drip line, and 1/4" soaker hose. The barbed fittings are pushed into the inside diameter of the 1/4" micro tubing, 1/4" drip line and 1/4" soaker hose for a very tight-fitting connection. The barbed fittings can be used for a two-way layout or for three-way layout of micro tubing, drip line, or soaker hose. The 1/4" barbed fittings are used to connect the end of all brands of 1/4" micro tubing with .140 ID to .170 ID. The barbed fittings can also be used to attach the micro tubing to the 1/2" or 3/4" drip tubing.
1/4" barbed fittings are made of high impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss and a range of drip emitter, bubbler, and micro sprayer flow rates leading to greater installation flexibility.
Features
1/4" barb coupling is used to joint two ends of 1/4" micro tube together.
1/4" Barbed Drip Fittings are used in the installation of all brands of 1/4" micro tubing, 1/4" drip line, and 1/4" soaker hose. The barbed fittings are pushed into the inside diameter of the 1/4" micro tubing, 1/4" drip line and 1/4" soaker hose for a very tight-fitting connection. The barbed fittings can be used for a two-way layout or for three-way layout of micro tubing, drip line, or soaker hose. The 1/4" barbed fittings are used to connect the end of all brands of 1/4" micro tubing with .140 ID to .170 ID. The barbed fittings can also be used to attach the micro tubing to the 1/2" or 3/4" drip tubing.
1/4" barbed fittings are made of high impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss and a range of drip emitter, bubbler, and micro sprayer flow rates leading to greater installation flexibility.
Features
1/4" barb coupling is used to joint two ends of 1/4" micro tube together.
1/4" Barbed Drip Fittings are used in the installation of all brands of 1/4" micro tubing, 1/4" drip line, and 1/4" soaker hose. The barbed fittings are pushed into the inside diameter of the 1/4" micro tubing, 1/4" drip line and 1/4" soaker hose for a very tight-fitting connection. The barbed fittings can be used for a two-way layout or for three-way layout of micro tubing, drip line, or soaker hose. The 1/4" barbed fittings are used to connect the end of all brands of 1/4" micro tubing with .140 ID to .170 ID. The barbed fittings can also be used to attach the micro tubing to the 1/2" or 3/4" drip tubing.
1/4" barbed fittings are made of high impact plastic and have the largest inside diameter in the industry with a higher flow rate capability and lower head loss and a range of drip emitter, bubbler, and micro sprayer flow rates leading to greater installation flexibility.
Features
This punch is used to pre-punch holes into main line tubing to permit installation of micro insert fittings.
Swivel Adapter Female Hose Thread (FHT) with washer x 3/4" Male Pipe Thread (MPT)
Male Hose Thread x 3/4" Male Pipe Thread
On-Off device to control the water flow in low pressure irrigation systems.
Hose clamps required for waterproof connection.
On-Off device to control the water flow in low pressure irrigation systems.
Hose clamps required for waterproof connection.
The self-piercing insert connector takes away the need for a hole punch. Simply put around any 1/2 in. irrigation tubing and squeeze the ratchet mechanism to provide a secure water tight fit. Easily installs without the use of special tools or glues.
